| Quantity: | |
|---|---|
PP heat shrink plastic sleeve backing is fabricated from a thermally stabilized, ultraviolet resistance, semi-rigid polyethylene-based backing and it is radiation cross-linked. PP heat shrinkable plastic sleeve inner layer is a high shear strength co-polymer adhesive. For better corrosion protection, solvent-free two-component liquid epoxy is recommended to use together with a PP heat shrink plastic sleeve.
3PP heat shrink sleeves are widely used in various industries, including:
Oil and Gas: Protecting pipeline joints and welds from corrosion.
Water Supply: Ensuring the integrity of water pipelines.
Construction: Used in the protection of electrical cables and other infrastructure components.
Item | Test temperature | Unit | Result | Test method |
PP backing | ||||
Tensile strength | 23℃ | MPa | ≥30 | ASTM D638 |
Elongation | 23℃ | % | ≥550 | ASTM D638 |
Hardness | 23℃ | Shore D | ≥61 | ASTM D2240 |
Water absorption,24h | 23℃ | % | ≤0.1 | ASTM D570 |
Volume resistance | —— | Ω.cm | ≥2*10^16 | ASTM D257 |
Low temperature brittleness | —40℃ | pass | ASTM D746 | |
Dielectric strength | —— | KV/mm | ≥25 | ASTM D-149 |
Adhesive | ||||
Melt point | —— | ℃ | 154 | ASTM D3418 |
Lap shear strength | 23℃ | MPa | 5.5 | ISO21809-3 |
100℃ | MPa | 0.55 | ISO21809-3 | |
Low temperature brittleness | -40℃ | —— | pass | ASTM D746 |
Ring-and-ball softening point | —— | ℃ | ≥150℃ | GB/T 4507 |
| Installed sleeve | |||||
Highest design temperature | —— | ℃ | 100 | —— | |
Thickness | —— | mm | backing≥1.0 adhesive≥1.5 | ISO21809-3 Appendix A | |
Cathodic disbandment, 28d | 23℃ | mm | 7.0 | ISO21809-3 | |
95℃ | mm | 15.0 | |||
Peeling strength （10mm/min） | To steel with primer | 23℃ | N/mm | 9.8 | ISO21809-3 Appendix D |
100℃ | 3.1 | ||||
To coating layer | 23℃ | 6.4 | |||
100℃ | 2.4 | ||||
28d,Tmax , peeling | To steel with primer | 23℃ | N/mm | 8.5 | ISO21809-3 Appendix I |
To coating layer | 5.5 | ||||
| Ordering Information | ||
Select sleeve width that will overlap onto the mill-applied coating by 2 inches( 50mm) minimum on each side of the weld joint. Take a 10% shrinkage during installation of sleeve width into account when calculating the minimum sleeve width. | Range for available dimension: | |
Sleeve length for 24 inch pipe | Length of PE shrink sleeves | |
Sleeve width | We can provide 450mm, 480mm, 500mm, 520mm and 550mm supplied PE shrink sleeves width. | |
Sleeve thickness | We can provide 1.8mm, 2.0mm, 2.2mm, 2.5mm, 2.8mm , 3.0mm and 3.2mm supplied PE shrink sleeves thickness. | |
Primer thickness | There are two kinds of primer application way, wet film and dry film. We can provide 120um, 150um, 200um, 300um and 400um primer thickness.0 | |
Hot tags: Polypropylene heat shrinkable sleeve for 24-inches pipe, 3lpp, 3lpp coating, 3lpp pipe coating, external coating of pipelines, gas pipe corrosion protection, pipeline corrosion coating, pipeline corrosion control, pipe coating systems, pipe coating companies, wholesale, custom, manufacturers, suppliers, manufacturing company
